Difference between revisions of "Stone Rose Install"

From Archive | Chen Chen & Kai Williams
Jump to navigation Jump to search
Line 33: Line 33:
|Black washers are intended to be removed.
|Black washers are intended to be removed.
|-
|-
| 4. Make sure that the cardboard cutout is as near to the end of the pegs as possible to get correct spacing between petals.||
| 4. Install light bulbs in sockets.|
|
|-
|-
| 5. Keep petals all in one direction. If needed, mark front of petals with tape to clarify. ||
| 5. Power can be restored and sconce tested.
|
|-
|-
| 6. If any petals crack during drilling process, set them aside for gluing/fiberglass. ||
| 6. Unpack rose heads carefully and remove the 3 black thumb screws.
|Rose heads are extremely fragile.
|-
|-
| 7. Drill with smallest bit. 4mm. Drill very gently. Place on 380 speed.
| 7. Slide the rose over the bulb and socket.  
| Too much pressure on the drill press will crack the stone pieces. Quartz is a hard stone, but can be brittle.  
| Secure rose head to stem with 3 black thumb screws.
|-
|-
| 8. Only use the drill press to start the hole and use a hand drill to go all the way through. The drill press' pressure can crack the stone and the hand drill allows you to slowly angle the cut for less pressure and will go faster. ||
| 8. Repeat with second rose head. |
|
|-
|-
| 9. Wash off all oil in sink, dry with air. ||
| 9. Remove leaf petal from packaging.  |
|}
|
|
| 10. Attach leaf petal using felt washers and brass acorn nuts.   |
|
|
| 10. Attach leaf petal using felt washers and brass acorn nuts.  |
|
 
}
The brass and silver stem is uncoated and will patina over time. If desired patina can be removed with T-9 Boshield and red scotchbrite pads. Rose petals are made of quartz, a hard, nonabsorbent stone that can be cared for like glass. Each slice is unique and cannot be replaced.  If broken, they can be repaired by the studio.
<br>
<br>
The Stone Rose Table Light is an art piece and comes with no guarantees. However we will replace electrical components due to manufacturing defect and normal operational wear for 1 year (not included: impact damage, water damage, electrical surge damage). After 1 year, cost of repair will be evaluated. Shipping costs are not covered. Email [email protected] to make repair arrangements.

Revision as of 20:55, 7 August 2023

Stone Rose Install


Sconce 22XX Onwards
Included:
Stone Rose Stem
2 Rose head assemblies
1 Leaf petal
3 Candelabra base 15W T22 E12 bulbs
Felt washers
3 M4 brass acorn nuts
7 Black thumb screws
2 8-32 brass flat head screws with temporary washers

Sconces must be attached to flush wall mounted J-boxes. 120V. Dimmer compatible.


Install
Description Notes
2. Use WAGO connectors to connect sconce wires to wall wires. Polarity does not matter.
3. Use 8-32 brass flat head screws to attach sconce to J-box. Black washers are intended to be removed.
5. Power can be restored and sconce tested.
6. Unpack rose heads carefully and remove the 3 black thumb screws. Rose heads are extremely fragile.
7. Slide the rose over the bulb and socket. Secure rose head to stem with 3 black thumb screws.

} The brass and silver stem is uncoated and will patina over time. If desired patina can be removed with T-9 Boshield and red scotchbrite pads. Rose petals are made of quartz, a hard, nonabsorbent stone that can be cared for like glass. Each slice is unique and cannot be replaced. If broken, they can be repaired by the studio.

The Stone Rose Table Light is an art piece and comes with no guarantees. However we will replace electrical components due to manufacturing defect and normal operational wear for 1 year (not included: impact damage, water damage, electrical surge damage). After 1 year, cost of repair will be evaluated. Shipping costs are not covered. Email [email protected] to make repair arrangements.

Retrieved from "http://archive.cckw.us/index.php?title=Stone_Rose_Install&oldid=3170"